My WX60 arrived! I ordered it from The Saori Shed in Diss, which fortunately for me is only 20 minutes down the road. It’s in a really nice building and is a fun place to visit and try out Saori weaving for a couple of hours…which is what I did the summer before last, and why I decided to get one of these looms! Unfortunately I wasn’t feeling well when it arrived, but my mum is awesome and went to pick it up for me.
Out of the box it looked like this:
Putting the other bits on wasn’t hard, the instructions were pretty clear. I can’t actually remember everything I did, but I think it was just putting in the back warp roller, the harnesses and reed, the shelf, and the bobbin winder. I just needed a screwdriver for the shelf, and a hammer for the bobbin winder. Nice and simple. And because it came ready warped, it wasn’t long at all before it was ready to go!
And yes, my helpful helper also likes helping with weaving:
The warp that came with it was 6 metres x 150 threads of black cotton. This is 30cm wide on the loom. I figured with that much fabric I should be able to make a garment, so I picked a bunch of coordinating colours and got to weaving.
The initial plan was the grey non superwash coned yarn, and some teal leftover sock yarn. Then I decided it needed a bit of magenta, so found some sock yarn in that shade, and also shoved in some bits of merino fibre I had in teals blues and purple. There’s also a teeny bit of leftover handspun in grey and teal in there.
The final fabric off the loom was 5.15 metres long. And very hard to photograph on a windy day.
After wet finishing, the fabric was about 26 x 475cm. I say ‘about’ because my selvedges weren’t especially neat, so the width varied a little, and the length was very hard to measure cos it was so long!
After a lot of sketching and calculating, I figured out the easiest way to make it into a top. Unfortunately there wasn’t enough fabric for a hood, but I still love it.
And because someone asked how I made the pattern, here’s the basic info:
Each piece was zig zagged on both sides of the cut line before being cut, all sewn seams were somewhere between the width of my sewing machine foot and the 10mm guide, depending on how neat my selvedges were. Seams were ironed open between each stage of sewing.
I cut 4 pieces 40cm long, which I then sewed together into a tube for the body.
The remaining length was folded almost in half, with one side a couple of cm longer than the other, and cut. This gave me 2 pieces approximately the same as my arm span.
The longer piece was again cut in half.
The raw edges of this last cut were folded under and stitched to finish the front neck opening.
These two pieces were then joined to the body tube making sure the V was centered. The back strip was joined in the same way, making sure it was all lined up. The top sleeve seam was sewed, leaving a gap 5†either side of the centre for the neck hole. Finally the underarm seams were sewn.
Then I went round and folded under and sewed all remaining raw edges…the collar, the sleeves, and the bottom hem, and folded in and sewed the corners of the top front slit to give the neckline a shape I liked.
It took me about 3 weeks to weave the fabric, and less than 3 hours to sew it. I’m not 100% sure I like the big baggy sleeves, I may well taper them if I find the extra fabric gets in the way, but that’s an easy change to make.
And pretty much as soon as that was off the loom, I was planning the next thing. I did this!
Yup, my loom now has 4 harnesses. Adding the extra 2 harnesses was a lot simpler than I expected, but I needed help, partly because there was a screw that was too tight that I couldn’t undo, and partly because it’s a lot easier to hammer a cap onto the end of a rod with someone else holding the far end of the rod to stop it shifting rather than having to do it all myself. Still, it didn’t take long to do.
Then I figured out the easiest way to wind a warp while sitting down:
368 ends, and while I did need to take breaks cos my arm got tired, it’s way less tiring than direct warping the rigid heddle on top of the table. Although of course, now I have to actually thread all that onto the loom.